Aqua Pendant, Rings, Lathes and Moto GP.

April 16, 2010

      Replacement piece. This is a really nice coloured aqua but it had some rather contortionistic  inclusions, if I might use that word. So I had to carve and carve, all the time chasing the flaws. The pendant is therefor was also made in a contortionistic manner. Repousé  with 18kt yellow and white […]

Read the full article →

Spessartite Finished and Experimental Cutting

April 8, 2010

This is my latest main piece, finished from the Mr Spessartite post.  18ct gold with a nice .20ct diamond . This piece of jewellery uses all my skills as a gem cutter, goldsmith and setter. Nice and minimalistic. To answer Ski and Cathy, the cutting of this stone does clog up a lap, but I […]

Read the full article →

The Story of Mr Spessartite the Big Cheese.

March 31, 2010

  The other day as I was opening my workshop, I heard a tremendous commotion inside, screaming and running and then a volley of gunshots. Then complete and utter silence, I carefully looked around the corner, but everything seemed normal, except that my rough gem box was not in the same place that I had […]

Read the full article →

New Titanium and Gold Ring

March 11, 2010

I have made a similar titanium ring like this before. This one, however, has an emerald cut diamond in the center with little diamonds around it. And my client wanted it higher and broader than the first one. This type of ring is quite tricky to make. One reason is that the size has to […]

Read the full article →

Jewellery, Aquamarines and Lathe Work.

March 7, 2010

    This ring, made on commission and my clients design. 18ct white gold and a yellow gold tube. The opal doesn’t photograph so good, but it is actually a very nice stone I always sweat to set a delicate stone like this, because it isn’t mine and if I break it I can’t replace it. […]

Read the full article →

New Titanium Pendant and Carved Intarsia.

February 27, 2010

This is my latest Carved Aquamarine -Titanium- Gold-Diamond-Emerald pendant. It’s about 50mm high. About 30 hours of work. The Aqua can be spun, if you so desire. Everything is mechanically joined. The four screws at the bottom of the picture are made in this sequence: Head soldered onto threaded wire, and cut to length. Spacer […]

Read the full article →

New Laminations and a New Concept Stone.

February 24, 2010

With this one, I had hoped to get a vibrant purple. But it figures, because blue and red make purple, so pink and blue would give a sort of mauve colour. That would be the two triangles on either side. Ok, so this one I actually didn’t know what would come out. I made the […]

Read the full article →

A New Lathe and a New Sign.

February 20, 2010

  Got my new lathe. This is a small one, mostly for gem related work. I must say, for $650 from Grizzly.com it is probably one of the nicest bang for your buck machines that a jewellery shop can have. Nice and compact. Ok, you need to do some adjustments, tighten various things up, but […]

Read the full article →

The Tale of the Three Swinging Stones–Part 1

February 16, 2010

Once upon a time in land far, far away there lived an itsty beeni teeni weeni little diamond, called ‘Fraidy cat. She was a tiny little diamond, and even though she had 57 facets, she was only 1.2 mm across. So she was afraid of everything At night she used to shiver in fear when […]

Read the full article →

Hans Meevis’ Workshops Announce Two Major Achievements.

February 14, 2010

Ladies and Gentlemen, Behold! The first CZ in the world with a three phase inclusion. A solid, which in this case is a gold ball (AU), then a liquid, which is Di-Hydrogen Mono-Oxide and two gasses, namely Nitrogen and Oxygen. Produced in the workshops of Hans Meevis. Difficult to photograph too. This is the first sucessful […]

Read the full article →

WordPress Admin