The Gem and Jewelry World's foremost Resource on The Internet.
[Orchid] Mohs - On A Scale of One to Ten  
  [Thread Prev] [Message Prev]      [Date Index]   [Thread Index]      [Message Next] [Thread Next]
From: Sandra I. Smith
Date: Sun Nov 04 03:27:54 2001
 
     
========[ Invite a Friend - http://www.ganoksin.com/invite.htm  ]========


    Although gemstones are hard substances, they aren't indestructible.
    Some can be ruined by contact with certain chemicals, while others
    break easily. Many are susceptible to surface scratching, which can
    ruin them. 

    The harder a gem is, the more difficult it is to scratch. If soft
    gems are used in jewelry, they need to be in settings that will
    protect them, and worn with care. 

    Gems are usually rated on their hardness according to the Mohs
    (rhymes with nose) scale. Mineralogist Friedrich Mohs developed the
    scale in 1812. The Mohs scale ranks minerals from one to ten, with
    one being the softest and ten the hardest. 

    Mohs used the following minerals in establishing his scale: 

	1. Talc (soapstone)
	2. Gypsum (alabaster)
	3. Calcite
	4. Fluorite
	5. Apatite
	6. Feldspar
	7. Quartz
	8. Topaz
	9. Corundum (ruby and sapphire)
	10. Diamond


    Each mineral can be scratched by itself or any above it. None can be
    scratched by any below it. For example, topaz can scratch quartz,
    but it can't scratch corundum. Talc can be scratched by everything,
    and nothing but diamond will make a mark on diamond. 

    Most of the commonly used gems have a Mohs hardness of 6 or greater.
    The hardness of some gemstones may vary slightly, depending upon the
    direction in which they are scratched. Hardness may also deviate
    according to where the stone was found. Gemstones may be assigned a
    range of hardness, such as 5-6 for hematite, rather than a single
    number. Hardness is frequently abbreviated as the capital letter H
    followed by a number, so that agate is described as H 7. 

    The numbers on the scale classify minerals only by their hardness.
    That is, topaz is harder than quartz, which is harder than feldspar.
    It does not show by how much each gemstone is harder. Fluorite has a
    rating of 4 and topaz has a rating of 8. This doesn't mean that
    topaz is twice as hard as fluorite because its rating is twice as
    high. It means only that topaz is harder than fluorite. Newer scales
    used by gemologists organize the gems according to degree of
    hardness. However, the Mohs scale continues to be the most
    widely-used ranking. 

    Some comparisons to everyday items may help make the rankings easier
    to understand. Substances with a hardness of 2 or less may be
    scratched by a fingernail. A copper coin will scratch anything
    ranked at 3 or lower. Window glass has a hardness of 5 and may be
    scratched by most gemstones. A steel file will scratch all
    substances up to 7 1/2. 

    Quartz is the most common of all minerals and is an element in many
    gemstones, including amethyst and rock crystal. Quartz is found also
    in rocks, dirt, and sand. This means that most dust contains
    particles of quartz and therefore has a Mohs hardness of 7. Nearly
    all gemstones can be scratched by dust. For this reason, it is very
    important to never rub dust off any gem when cleaning it. 

    Following are the Mohs hardness of some popular gems. 

	8 1/2 Chrysoberyl
	7 1/2 Aquamarine, emerald
	7 Amethyst, tourmaline
	6 1/2 Peridot
	6 Moonstone, opal, turquoise
	5 Lapis lazuli
	4 Malachite
	3 Chryscolla


    The organic gems, which are not minerals, are all quite soft.
    Because of their variety, pearls may range from 2 1/2 to 4. Amber
    and ivory are softest at 2 1/2. Glass imitations of gemstones are
    usually 6 or less. 

    While the Mohs scale has its shortcomings, ranking minerals on a
    scale of one to ten is simple way to determine the degree of care
    and protection needed by gemstones. 


****Sandra I. Smith, Writer ****



____________________________________________________________________
T h e   O r c h i d   L i s t
Open Electronic Forum for Jewelry Manufacturing Methods and Procedures
____________________________________________________________________
Orchid FAQ:
~ http://www.ganoksin.com/orchid/faq.htm
Orchid Archives:
~ http://www.ganoksin.com/orchid/archive
Orchid Galleries:
~ http://www.ganoksin.com/orchid/gallery.htm
Invite a Friend:
~ http://www.ganoksin.com/invite.htm
____________________________________________________________________
Tips From The Jeweler's Bench - Article Archive
~ http://www.ganoksin.com/borisat/tip_sear.htm
The Jeweler's Selected Bibliography List
~ http://www.ganoksin.com/jewelry-books
Buy Orchid Jewelry:
~ http://www.ganoksin.com/shop
____________________________________________________________________
-Unsubscribe:
-Email: orchid-request AT ganoksin.com Body=unsubscribe subject=blank
____________________________________________________________________


  Click to Visit  
     
  Navigate:  
   
  Orchid Resources:  
   Join & Post
 Invite a friend to join Orchid
 F.A.Q
 Galleries
 BenchExchange
 Orchid Message Archives [Subject Index] [Date Index]

Ganoksin now offers a number of ways for you to stay on top of the latest from Orchid!

  1. My Yahoo - Do you have a My Yahoo page? If so, you can easily read the latest Orchid posts on your personalized page by adding this feed:Add Orchid to My Yahoo!
  2. Add Orchid to myGoogle Add to my Google
  3. Read Orchid with NewsGator and Microsoft Outlook Add Orchid to Your  NewsGator
Support Orchid! - If you believe in what we're doing, you can help!

 
     
     

© Copyright 1996 - 2008, The Ganoksin Project